Steel Profile Weight Calculator

Profile
Made
Pieces

This is the nominal mass from the nominal dimensions and a steel density of 7.85 kg/dm³. Delivered steel varies within the rolling tolerances, and the price is usually by actual weight.

Cold-formed hollow section: corner radii taken as in LST EN 10219-2 for calculation – outer 2T and inner 1T up to 6 mm wall, 2.5T and 1.5T up to 10 mm, 3T and 2T above.

Standard: LST EN 10219-2

Diagram
Total mass70.4kg
Mass per metre11.73kg/m
Surface to paint2.32m²
What to buy
  • Steel sections and bars70.4 kg

Rounded up to whole pieces and packs. Pack sizes come from your inputs or are typical ones — check with your supplier before buying.

Cross-section
Cross-section area14.95 cm²
Mass per metre11.73 kg/m
Outside surface per metre0.386 m²/m
Outer corner radius8 mm
Inner corner radius4 mm
All pieces
Mass of one piece70.4 kg
Total length6 m
Total mass70.4 kg
Outside surface, all pieces2.32 m²

Standards applied: LST EN 10219-2LST EN 10210-2


About this calculator

This calculator gives the weight of common steel sections: square and rectangular hollow sections (box sections), round tubes, flat bar or plate, round bar and square bar. Enter the size, the length of one piece and how many pieces you need, and you get the mass per metre, the mass of one piece, the total mass for transport or ordering, and the outside surface you will have to prime and paint.

Hollow sections have rounded corners, and the corner radius depends on how the section was made. Cold-formed sections (bent from strip and welded, the usual "profile tube" in a builders' merchant) are calculated with the corner radii of LST EN 10219-2; hot-finished sections with those of LST EN 10210-2. Both standards compute the nominal mass with a steel density of 7.85 kg/dm³, and so does this calculator.

Formula

square / rectangular hollow section (H × B × T):
  area      = 2T × (B + H − 2T) − (4 − π) × (ro² − ri²)
  surface   = 2 × (B + H) − (8 − 2π) × ro          per metre
  cold-formed:  ro = 2T, ri = T      (T ≤ 6 mm)
                ro = 2.5T, ri = 1.5T (6 < T ≤ 10 mm)
                ro = 3T, ri = 2T     (T > 10 mm)
  hot-finished: ro = 1.5T, ri = T

round tube (D × T):    area = π × (D − T) × T
flat bar (B × T):      area = B × T
round bar (D):         area = π/4 × D²
square bar (A):        area = A²

mass per metre = area × 7.85 kg/dm³
total mass     = mass per metre × piece length × pieces

Worked example

Ten cold-formed 100 × 100 × 4 mm box sections, 6 m long:

ro = 2 × 4 = 8 mm, ri = 4 mm
area           = 2 × 4 × (100 + 100 − 8) − (4 − π) × (8² − 4²)
               = 1536 − 41.2                     = 1494.8 mm² (14.9 cm²)
mass per metre = 1494.8 mm² × 7.85 kg/dm³        = 11.73 kg/m
total mass     = 11.73 × 6 m × 10                = 704 kg
surface        = 400 − (8 − 2π) × 8              = 386 mm → 0.386 m²/m
paint          = 0.386 × 60 m                    = 23.2 m²

The published EN 10219-2 table gives 14.9 cm² and 11.7 kg/m for this size.

FAQ

Why is the steel I bought heavier or lighter than this? The result is the nominal mass. Real sections are rolled within thickness and mass tolerances, and some suppliers sell sizes slightly under the nominal wall. If you pay by weight, the weighbridge decides.

Cold-formed or hot-finished — which do I have? Most box sections sold for fences, gates, frames and canopies are cold-formed (welded seam, tighter corners). Hot-finished sections are mainly used for heavier structural work and have smaller, sharper corners. The difference in mass is small, usually under 2 %.

Does it work for stainless steel or aluminium? No — the density is fixed at 7.85 kg/dm³ for carbon steel. Stainless steel is a few percent heavier, aluminium about a third of the weight.

Is the paint surface the inside too? No, only the outside. Hollow sections are usually closed at the ends and only painted outside.

Does the calculator check if the section is strong enough? No. It only gives mass and surface. Whether a section can carry a load must be checked by a structural design.